Water on the basement floor means the pump has stopped or cannot keep up
Look in the sump pit first. If the water is near the rim and the pump is silent, check that it is plugged in and that the breaker or the reset button on the outlet has not tripped. Then lift the float gently with a stick. If the pump starts, the float was caught on the pit wall or the cord.
If the pump runs but the water keeps rising, the pump is worn, the intake is clogged with silt, or the discharge line is frozen or blocked outside. Go out and look at the end of the discharge pipe. If no water comes out while the pump runs, the problem is the line, not the pump.
Keep away from anything electrical near the water. Never stand in water to reach an outlet. Turn the breaker off at the panel first. If water is still coming in, call an emergency plumber. While you wait, lift boxes off the floor and take photos for your insurer.
A pump that hums, short-cycles or never stops is close to failing
A hum with no water moving usually means a jammed impeller or a failing motor. A pump that starts and stops every few seconds often has a failed check valve. The water in the discharge pipe falls back into the pit each time the pump stops, so it pumps the same water again. You can hear it as a thump and a gurgle at shut-off.
A pump that runs nonstop in dry weather may have a float stuck in the on position, or groundwater may be coming in faster than the pump can move it. Either way the motor wears out fast. If the pump is rusty, noisy and as old as the house, replace it before spring rather than after it fails.
To test it, pour a pail of water slowly into the pit until the float rises. The pump should start, empty the pit and stop by itself. The sump pump guide goes through it step by step.
The discharge goes away from the foundation, never into the septic
Basements take water in the spring. The City of Kingston's basement flooding advice for spring is to test the sump pump and lengthen its discharge hose away from the foundation, and Sydenham basements get the same thaw. Snowmelt and rain soak the ground and fill the footing drains, so the pump runs more in a few weeks than in the rest of the year. That is when a weak pump or a short discharge shows up.
A discharge that ends against the wall sends the water back down to the footing drains, and the pump moves it around again. Extend the line so it empties well away from the house, onto ground that slopes away. In winter a line that sags and holds water will freeze, and the pump then pushes against a blocked pipe. Run the line so it drains empty between cycles.
Never connect a sump pump to a floor drain, a laundry tub or anything else that runs to the septic tank. Every drain inside a Sydenham house goes to its own septic system, and groundwater from the pit floods the tank and the leaching bed. The township's storm pipes in the village carry stormwater only. See what drains where in a Sydenham house.
If the discharge line is to be buried, request a locate through Ontario Dig Authority before anyone digs. Public locates do not mark private lines, so the pipe out to your septic tank has to be found some other way first.
A battery backup keeps the pit dry when the power goes out
The storms that bring the heaviest rain also bring power cuts, and a main pump with no power does nothing. A battery backup is a second pump in the same pit, set a little higher than the first. It runs off a sealed battery when the main pump stops or falls behind.
It needs room in the pit, a check valve and a charger on a nearby outlet. Most have an alarm that sounds when the backup starts, which tells you the main pump has failed. Batteries wear out. Check the date on yours, replace it on the manufacturer's schedule, and test the backup by unplugging the main pump with water in the pit.
A backup is most worth having where the sump is the only thing keeping the basement dry, and most of all where the basement is finished.
Which Sydenham houses have a sump, and what goes wrong in each
The newer lots along Rutledge Road and Stage Coach Road have PEX water lines, drains to a septic system and a sump pump on the footing drains. In these houses the pump does most of the work of keeping the basement dry, and a failed pump is the usual cause of a wet floor. Test it every spring.
Houses from 1961 to 1980 often have footing tile and a basement floor drain but no sump. Before deciding anything, find out where the floor drain goes. If the basement takes water every spring, a sump pit on the footing tile can carry groundwater outside instead of letting it reach the tank.
The older houses on George Street and Mill Street have stone basements with no footing drain and no sump, and water seeps through the walls at thaw. A pit and pump at the low corner can keep the floor dry. It does not stop the seepage itself.
How a sump pump visit goes
The plumber fills the pit and watches the pump start and stop. They check the float, the check valve and the discharge outside, and look for silt and gravel in the pit. You are told whether the pump needs cleaning, a part or replacing, and the price is written down for you to approve before work starts.
For a new pit, the plumber finds the low point, cuts the floor, sets a lined pit, connects the footing drains where they can be reached and runs the discharge out through the wall. A new installation or a change to the drains may need a building permit, and the township building department decides whether yours does. Work is performed by licensed plumbers (306A Certificate of Qualification).
Ask for a written price for a test, a replacement or a battery backup.
